Custom Marine Sunshades · Delray Beach · Since 1974

Robalo Sun Shades, Cut to Your Deck

Robalo builds in Nashville, Georgia, and the current lineup runs from the 16 foot R160 to the 36 foot R360, with a bay boat line and a dual console line alongside the center consoles. That means "can you shade a Robalo" has four different answers depending on which one is in your slip.

The common thread is that Robalos get bought by people who do more than fish. The boat goes to the sandbar on Saturday and the reef on Sunday. A hardtop or T-top shades the helm on both days and does nothing for the bow, which is where everyone sits once the anchor is down.

We have been building custom Sunshades in Delray Beach since 1974. The shade is patterned in 3D to your deck, sewn in Stamoid, and goes up in under 60 seconds by one person. Full kits from $1,895, shade only from $845 if you already have poles, free shipping anywhere in the United States, no sales tax outside Florida.

We are not affiliated with Robalo. We build canvas that fits their boats.

Four Robalo layouts, four different shades

R-series center consoles (R160 through R360). The standard order. A bow Sunshade attaches to quick-release mounts on the forward edge of the T-top or hardtop, flies out over the bow seating, and tensions to two carbon fiber telescoping poles standing in the forward rod holders. On the R222 and R230 that is a two-pole panel. The R250, R270 and R300 have enough beam that we often go to four poles so the panel stays flat in a breeze. The R360 is a different animal: 36 feet 6 inches, a cabin in the console, and a bow lounge the size of a small patio. On that boat we build bow and aft together more often than not.

Explorer models (R202EX, R222EX, R232EX). Same hull family, more open deck. More freedom in where the poles stand, but we confirm the forward rod holders exist before we quote. If they do not, we add Gemlux rod holders during the install.

Cayman bay boats (206, 226, 246, 266, and the SD versions). The Caymans live on the flats with no overhead cover unless the owner added a T-top. The bow is a casting deck, not a lounge. The shade has to cover it without putting a pole in the middle of it, so the forward poles go outboard and aft of where you stand to throw. On a Cayman with no top at all we build a freestanding four-pole rig.

Dual consoles (R207, R257, R277, R317). The windshield changes everything. There is no T-top on most of these, and the bow is a sunken seating area with a walk-through. We mount the aft edge of the shade to the top of the windshield frame or to a hardtop if the boat has one, and run the forward edge to poles in the bow. These get the most daily use of anything we build for Robalo, because the whole point of an R257 is six people aboard at anchor.

Robalos we build for

  • R160, R180 and R200. Small hulls. Two poles, a compact bow panel, freestanding on the R160 if there is no top.
  • R222 and R230. The volume models and the cleanest build in the range. Two-pole bow shade off the T-top.
  • R250, R270 and R300. Four-pole bow panels; bow and aft together on the R300 for anyone who fishes the cockpit.
  • R360. Bow and aft, six poles, large panels. Call us on this one.
  • R202EX, R222EX and R232EX. Open-deck Explorer hulls. Pole placement is the job.
  • 206, 226, 246 and 266 Cayman, plus the 246 Cayman SD and 266 Cayman SD. Bay boats. Casting deck coverage without blocking the casting deck.
  • R207, R257, R277 and R317. Dual consoles. Windshield-frame or hardtop mount, poles forward.

See all our custom Sunshades. We also build for Grady-White, Sea Fox, Key West and Sportsman.

What a Robalo shade is actually made of

Every shade we build is Stamoid, and that is a deliberate choice. Stamoid is 100% waterproof, blocks UVB completely, and is backed by a 5-year warranty. In practice it lasts a good deal longer, because a Sunshade is deployed for a few hours at a time rather than left standing in the sun year round, and the shades we have built have run 10 years and more. It comes in 14 colors, so a shade can sit against a Robalo's gelcoat and factory canvas without looking like an afterthought.

The sewing is where cheap shades fail first, so ours is sewn with lifetime thread (PTFE). Sides are double-reinforced, corners are triple-reinforced because the corners carry all the tension, and every edge is cut on a catenary curve. A straight-cut edge sags in the middle and flaps. A catenary edge pulls tight and clean across its whole length when the corners are tensioned.

The panel is patterned in 3D to your boat's actual measurements and built to the mount-to-mount number to an eighth of an inch. A shade cut to a generic 23 footer will either stop short of a Robalo's bow or pull the poles inward.

Poles are black carbon fiber telescoping poles as standard, stainless on request. Where a Robalo needs rod holders added, we install Gemlux rod holders only. Our guide on ordering a custom Sunshade from out of state covers the measuring when we cannot see the boat.

Measured at the boat in South Florida, shipped free everywhere else

From Miami to Jupiter we come to the boat. A technician measures at your slip or on the trailer, we build in Delray Beach, and we come back and install. The truck carries rod holders, poles, mounts and hardware, so a local install including drilling and fitting new rod holders is finished in one visit.

Robalo sells through a national dealer network, so most of the Robalos we shade are not in Florida. For those you measure with our card and a phone or video walkthrough, we build to those numbers, and it ships free anywhere in the United States with no sales tax outside Florida. Most owners self-install in an afternoon with a drill and a tape measure.

Either way, you can run at up to 25 mph with the shade up, and pulling it tight buys a little more. It comes down in about 30 seconds and goes back up in under 60, so running fast is a non-issue. It stuffs into its bag and can be stowed wet.

Questions

Robalo Sun Shades FAQ

Does a Sunshade work on a Robalo dual console with a windshield and no T-top?

Yes. On an R207, R257, R277 or R317 we mount the aft edge of the shade to the top of the windshield frame or to a hardtop if the boat has one, and the forward edge tensions to telescoping poles standing in the bow. The panel sits high enough that people can sit normally underneath it, and the walk-through stays clear. If there are no rod holders forward, we add Gemlux rod holders during the install, or ship them with the kit for a self-install.

My Cayman has a poling platform. Where do the aft poles go?

Usually they do not need to. On a Cayman the shade people want is over the forward casting deck, where there is nothing overhead at all. If the boat has a T-top we mount the aft edge to the top and run two poles forward, outboard and behind the casting position so you can still throw. If there is no top we build a freestanding four-pole rig. The poling platform only matters if you want aft coverage too, and then we work around the platform legs. Send us a photo of the stern and we will tell you what is possible.

Will mounting to the factory Robalo T-top damage it?

The quick-release mounts are screwed to the top on the console side, and on a factory Robalo top that is a routine install. We are drilling the top's forward edge, not the hardtop skin where it could flex, and the mounts are small stainless fittings. If you prefer not to drill the top at all, the freestanding four-pole option stands entirely in rod holders and touches nothing above deck.

The R222 and R230 have a bow filler cushion. Does the shade cover the whole bow lounge?

That is the point of it. The shade runs from the forward edge of the T-top out to the forward poles, which on an R222 or R230 puts the forward edge at or near the bow rail. The whole seating area, filler cushion included, sits under it. The height is set so an adult can sit upright and most people can stand in the center without ducking. If you have a bow table fitted, mention it when you order so the poles clear it.

I bought my Robalo from a dealer outside Florida. How does ordering work?

Order online, measure with our card, and we build it from your numbers. The card asks for the five measurements that matter, then one of us gets on the phone or a video call with you at the boat to confirm them. Because Robalo builds a lot of each model, we usually already know the layout and are checking your numbers against boats we have patterned before. The shade ships free anywhere in the United States with no sales tax outside Florida.

How many poles does a bow shade need on an R300 or R360?

Four on the R300 and six for bow and aft together on the R360. A two-pole panel is fine on a 22 or 23 foot bow, but once the panel is wide enough to catch a real breeze the extra poles keep it flat and keep the tension even across the catenary edges. Pole count is included in the kit price and we size it to the boat, so you are not choosing. We confirm the count when we confirm your measurements.

Shade the bow of your Robalo

Order the full kit from $1,895, the shade only from $845, or call (561) 270-6922, 8am to 4pm Eastern, Monday through Friday.

Or call (561) 270-6922
Free Quote Within One Business Day

Tell us about your Robalo

Send a few details and a couple of photos and we reply with a fixed price on a shade built for your boat. Local to South Florida? We come to you. Anywhere else in the country? We ship you a kit.

Prefer to talk? Call or text (561) 270-6922, 8am to 4pm ET Monday to Friday.
This field is for validation purposes and should be left unchanged.
Two photos help most: your T-top from the side, and your rod holders. Photos on your phone? You can also text them to (561) 270-6922.
Drop files here or
Accepted file types: jpg, jpeg, png, heic, webp, Max. file size: 20 MB, Max. files: 4.

    Let's Talk

    This field is for validation purposes and should be left unchanged.

    Start Your Project

    Let’s start the conversation. Share a few details and we will be in touch.