Majek Sun Shades, Cut to Your Deck
Majek has hand-built shallow-water boats in Corpus Christi, Texas since 1982, and the three lines on their site today are three different answers to the same question: how shallow can a boat run and still handle the Laguna Madre when the wind gets on it. The Redfish Line is the tunnel-hull flat-bottom that started it, the Xtreme is a low-sided tournament V-hull, and the Illusion splits the difference with two feet of V on each side and four feet of flat down the middle.
None of the three gives you anywhere to get out of the sun. That is not a criticism; it is the design brief. A Majek is low, open and fast, and from Baffin Bay to the Land Cut there is no shade on the water that you do not bring with you.
We pattern the shade in 3D to your measurements and sew it in Delray Beach, Florida. Full kits from $1,895 with carbon fiber poles, quick-release mounts and hardware. Shade only from $845 if you already have poles. Ships free to Texas, no sales tax. See all our custom Sunshades.
We are not affiliated with Majek Boats. We build canvas that fits their boats.
What a Majek's hull and sides mean for the shade
Low sides. Majek describes the Redfish Line as low-sided with deep tunnels, and the Xtreme as a sleek, low-sided tournament boat. Low freeboard puts the gunwale rod holders, and so the base of every pole, close to the water. The shade has to clear head height from a low start, so the poles telescope taller than on an offshore hull, and we cut the catenary deeper so the panel stays tight and clean with more pole showing.
Aluminum or nothing. Majek's custom options list center console, seating, aluminum and hull color. Aluminum, on the Texas coast, means a top or a leaning post or both. With an aluminum top, the console-side edge of the shade clips to quick-release mounts screwed to it and two carbon fiber poles carry the outboard corners. With no aluminum, the shade is a freestanding four-pole rig, every corner on a pole in a rod holder, nothing touching the console.
The fishing platform forward. Redfish Line boats come with a full-size console and a fishing platform. The platform is the whole reason you bought the boat, so the poles go outboard of it and the panel sits above head height, keeping the casting arc clear. When it is time to pole or wade, the shade comes down in about 30 seconds and goes in the bag.
The Illusion's hybrid bottom. The hull shape under the waterline does not change the shade; the deck does. The 22' and 25' Illusion and the M2 Illusion carry a usable forward deck with enough width that a two-pole bow shade is the normal order, and the 25 is where four poles forward and an aft panel start to pay.
Majeks we build for
Model names as Majek writes them on majekboats.com.
- Redfish Line: 16' Texas Skiff, 18' Redfish, 21' Redfish, 25' Redfish. Tunnel hulls with an 8" draft and the lowest sides in the line. Freestanding two-pole bow shade on the 16 and 18; the 21 and 25 take bow and aft, which together saves about 10%.
- Illusion: 22' Illusion, 25' Illusion, M2 Illusion (22' 6"). The hybrid hull. Two-pole bow shade off an aluminum top or freestanding; four poles forward on the 25.
- Xtreme. The low-sided tournament V-hull, built in several lengths. Same approach as the Illusion at each length.
- Texas Slam. No longer on Majek's current site, but there are plenty on the water, and we pattern to measurements, not to a model year.
Other Texas and Gulf bay boats we build for: Blue Wave, Pathfinder and Sportsman.
The same build for a Texas Skiff as for a Superyacht
- Stamoid fabric. One fabric, chosen on purpose. Stamoid is 100% waterproof, blocks UVB completely, and is backed by a 5-year warranty. In practice it lasts a good deal longer, because a Sunshade is deployed for a few hours at a time rather than left standing in the sun year round, and the shades we have built have run 10 years and more. 14 colors, so it can match a Majek's hull color.
- Lifetime thread (PTFE) on every seam. Thread is where cheap shades fail first.
- Double-reinforced sides, triple-reinforced corners. On a low boat the corners take the whole wind load, and there is a lot of wind on the Laguna Madre.
- Catenary curves on every edge. The edges are cut in a shallow curve so that when the corners are tensioned the whole edge pulls tight and clean, no sag, no flap. A straight-cut edge sags in the middle and flaps.
- Patterned in 3D to your boat, built to the mount-to-mount number to an eighth of an inch.
Poles are black carbon fiber telescoping poles as standard, which matters more on a Majek than on most boats because low sides mean more pole extended, and carbon stays stiff at full extension. Stainless on request. Where the boat needs rod holders added for the poles, we specify Gemlux rod holders and tell you exactly where to drill. See carbon fiber telescoping Sunshade poles.
You measure, we build, it ships free to Texas
We measure and install at the boat from Miami to Jupiter, Florida. Everywhere else, including Corpus Christi, Port Aransas, Rockport, Port Mansfield and the rest of the Texas coast, you measure with our card and a phone or video walkthrough, we pattern and sew in Delray Beach, and the kit ships free to your door with no sales tax outside Florida. Most owners install it in an afternoon with a drill and a tape measure.
Up in under 60 seconds by one person, down in about 30. You can run at up to 25 mph with it up, and pulling it tight buys a little more. On a boat built to run fast across open bay, you drop it for the run and put it back up at the spot, which takes a minute, so running fast is a non-issue.
Call (561) 270-6922. We answer the phone 8am to 4pm Eastern, Monday through Friday, which is 7am to 3pm in Corpus Christi.
Majek Sun Shades FAQ
The Illusion is flat down the middle and V on the sides. Does the hull shape change the shade?
No. The shade never sees the bottom of the boat. What it sees is the deck: the width between the gunwale rod holders, the height of the top if there is one, and the distance from the mount point to the bow rod holders. The Illusion's hybrid bottom gives it a deck that is wider forward than a pure V-hull of the same length, which is good for a bow shade, because a wider pole stance pulls the catenary edges tight with less tension. We pattern to the deck numbers you send.
My Redfish Line sits low. Will the poles have to be too tall to clear my head?
They will be taller than on an offshore boat, and that is fine. The carbon fiber poles telescope to the height the pattern calls for and lock there, and carbon stays stiff at full extension where a cheaper pole would whip in the wind. We set the panel height from the deck the pole stands on and the height of the people who use the boat, so tell us if you are tall. The deeper catenary we cut for low boats keeps the panel tight and clean with the extra pole showing.
The Xtreme has low sides and a tournament layout. Where do the poles stand?
In the gunwale rod holders, outboard of the casting decks, same as any bay boat. On a tournament layout the question is which rod holders, because you need the others for rods. We place the shade poles in the pair nearest the corners of the panel and leave the rest for fishing, and if the boat has no holder where a pole needs to be, we specify a Gemlux rod holder at that exact position. The poles come out in seconds when you want every holder back.
I still run an older Texas Slam. Can you shade a model Majek no longer builds?
Yes. We never build from factory drawings, we build from your boat. The measure card asks for the mount-to-mount distances, the top height if there is one, and a few photos, and the shade is patterned in 3D to those numbers. Whether the model is on the builder's site this year does not come into it. A Texas Slam with an aluminum top gets the same quick-release mounts and two-pole bow shade as a new Illusion; one without gets a four-pole freestanding rig.
Can I order the shade before I take delivery of a new Majek from the dealer?
You can order it, but we would rather measure the real boat. Majek builds with custom options, so the console position, the aluminum and the rod holder layout on your boat can differ from the one on the showroom floor. The best sequence is to order, then send the measurements the day the boat is in your driveway with the aluminum mounted. Measuring at the dealer before delivery works too; we just need the boat rigged the way it will be when the shade goes on.
Is there sales tax on a Majek Sunshade shipped to Texas?
No. We ship from Florida and collect no sales tax on orders shipped outside Florida, so the price you see online for a kit shipped to Corpus Christi is the price you pay, and shipping is free anywhere in the United States. Full kits start at $1,895 with poles, quick-release mounts and hardware, shade only from $845 if you already have poles, and bow and aft ordered together saves about 10%. Fixed price, spec written out before you approve.
More builders we shade
BlackJack · Haynie · NauticStar · Sea Born · Shoalwater · Blue Wave · Carolina Skiff · Crevalle
Sunshades by boat type
Center Console · Dual Console · Sport Fisher · Yachts · Nordhavn · Superyachts
How we build them
How a Sunshade Is Made · Why Stamoid · Carbon Poles · Gemlux Rod Holders · What It Costs · Running With It Up · Ordering Out of State
Measured and installed at your boat
Miami · Fort Lauderdale · Palm Beach · Jupiter · Stuart & Fort Pierce · Charleston SC
Shade a boat built for the shallowest water in Texas
Order the full kit, shade only, or call (561) 270-6922, 8am to 4pm Eastern, Monday through Friday.
Or call (561) 270-6922Tell us about your Majek
Send a few details and a couple of photos and we reply with a fixed price on a shade built for your boat. Local to South Florida? We come to you. Anywhere else in the country? We ship you a kit.
Prefer to talk? Call or text (561) 270-6922, 8am to 4pm ET Monday to Friday.