Haynie Sun Shades, Cut to Your Deck
A Haynie is a Texas boat in the most literal sense. Rayburn Haynie started laying up fiberglass bay boats in Seadrift, and the 23 Big Foot he introduced there is still the hull people picture when they hear the name. Since 2006 the company has belonged to Chris Coulter, and the boats are built and sold through Chris's Marine in Aransas Pass, a few minutes from Rockport and the Lydia Ann Channel.
That coast is the point. Aransas Bay, Copano, the Laguna Madre down to Baffin and the Land Cut: wide, shallow, open water with nothing between the boat and the sun. A Haynie is built to run it fast and float it shallow, and the Sunshade has to fit that boat the way it is actually rigged, which on the Texas coast usually means an aluminum setup rather than a fiberglass hardtop.
We pattern the shade in 3D to your measurements and sew it in Delray Beach, Florida. Full kits from $1,895 with carbon fiber poles, quick-release mounts and hardware. Shade only from $845 if you already have poles. Ships free to Texas, no sales tax. See all our custom Sunshades.
We are not affiliated with Haynie Bay Boats or Chris's Marine. We build canvas that fits their boats.
Aluminum setups, console choices and what they mean for the shade
Haynie lists most hulls with a console choice (regular, deluxe, tournament or HCB) and either an aluminum setup or no aluminum mounted. That one line on the spec sheet decides the shade.
With an aluminum setup. An aluminum top over the console gives the shade something to hang from. The console-side edge of the panel clips to quick-release mounts screwed to the aluminum, two carbon fiber poles carry the outboard corners, and the top takes most of the load. Aluminum tops are often narrower and lower than a fiberglass hardtop, so we measure the top's actual edge and set the pole height so the panel runs level or rises slightly toward the poles, which keeps rain draining off the outboard edge instead of pooling against the console.
With no aluminum mounted. The shade becomes a freestanding four-pole rig, every corner on a telescoping pole standing in a rod holder. Nothing attaches to the console. It goes up in about the same time either way.
The console position. A Haynie console sits where the owner wanted it, which varies more than on a production boat. We do not assume. The mount-to-mount number you send us is the number we build to, to an eighth of an inch.
Cat hulls. The 21' Super Cat, 23' Super Cat, 23' Cat and 24' Cat carry their beam well forward, so the forward deck is nearly a rectangle and the bow shade comes out close to square with a wide pole stance. That is easier to tension tight and clean than a pinched V-bow.
Haynies we build for
Model names as Haynie writes them on hayniebayboats.com.
- 20' Little Foot and 21' Z 21. Compact hulls, two-pole bow shade, freestanding if no aluminum is mounted. Bags small enough for the console.
- 23' Big Foot. The original, and still the all-around family boat in the line. Bow shade over the forward deck is the common order; add the aft panel for the full boat.
- 23' Magnum and 25' Magnum. Built to eat the chop, with more freeboard than the flats hulls. Four-pole bow panels start to make sense at 25 ft, and bow and aft together saves about 10%.
- 24' High Output and 24' VLS. The go-fast tournament hulls. Owners here tend to want a shade that drops in 30 seconds for the run and goes back up at the spot. That is what it does.
- 21' Super Cat, 23' Super Cat, 23' Cat, 24' Cat. Wide forward decks, square bow panels, and the aft shade off the aluminum or on its own pair.
An older Haynie or a custom layout changes nothing for us; we pattern to measurements, not to a model number.
Other bay boats we build for: Pathfinder, Sportsman, Tidewater and Blue Wave.
Built for the Coastal Bend sun
- Stamoid fabric. One fabric, chosen on purpose. Stamoid is 100% waterproof, blocks UVB completely, and is backed by a 5-year warranty. In practice it lasts a good deal longer, because a Sunshade is deployed for a few hours at a time rather than left standing in the sun year round, and the shades we have built have run 10 years and more. 14 colors.
- Lifetime thread (PTFE) on every seam. Thread is where cheap shades fail first, and in Coastal Bend sun they fail fast.
- Double-reinforced sides, triple-reinforced corners. The corners carry everything when the afternoon wind comes across Aransas Bay.
- Catenary curves on every edge. The edges are cut in a shallow curve so that when the corners are tensioned the whole edge pulls tight and clean, no sag, no flap. A straight-cut edge sags in the middle and flaps.
- Patterned in 3D to your boat, built to the mount-to-mount number to an eighth of an inch.
Poles are black carbon fiber telescoping poles as standard, stainless on request. Where the boat needs rod holders added for the poles, we specify Gemlux rod holders, the best made in our experience, and tell you exactly where to drill. See carbon fiber telescoping Sunshade poles for why we stand on carbon.
You measure, we build, it ships free to Texas
We measure and install at the boat from Miami to Jupiter, Florida. Everywhere else, including Aransas Pass, Rockport, Corpus Christi, Port Aransas and the rest of the Texas coast, it works like this: call (561) 270-6922 or order online, we send a measure card and walk you through it on the phone or on a video call, we pattern and sew the shade in Delray Beach, and it ships free to your door with no sales tax outside Florida. Most owners install it in an afternoon with a drill and a tape measure.
Up in under 60 seconds by one person, down in about 30. You can run at up to 25 mph with it up, and pulling it tight buys a little more; for the long run down the Intracoastal, dropping it is a half-minute job, so running fast is a non-issue.
We answer the phone 8am to 4pm Eastern, Monday through Friday, which is 7am to 3pm in Aransas Pass.
Haynie Sun Shades FAQ
My Haynie has an aluminum setup, not a fiberglass hardtop. Can the shade mount to aluminum?
Yes, and most Texas boats we build for are rigged exactly that way. The quick-release mounts screw to the aluminum top's edge the same way they screw to a fiberglass top, and the panel clips on and off in seconds. Aluminum tops are often narrower than a hardtop, so we measure the top's actual outer edge rather than the console, and the 3D pattern accounts for the difference between the top width and the pole stance at the gunwale. Send a photo of the top and we will tell you where the mounts go.
Which Haynie models are big enough for bow and aft together?
Any of them can carry both, but the ones where it pays are the 25' Magnum, the 24' Cat and the 23' and 24' hulls with an aluminum top, because the top gives the aft panel something to fly from and there is enough deck both ways to be worth covering. On a 20' Little Foot or a Z 21 most owners stop at the bow shade and get most of the benefit. Bow and aft ordered together saves about 10%.
The Big Foot has a raised forward deck. Does the shade clear it?
Yes. The pole height is set from the deck the pole stands on, not from the cockpit sole, so a raised casting deck simply means the panel sits a little higher over the bow than over the console. We pattern that rise into the shade in 3D, and the catenary edges keep it tight and clean across the step. The result is head height everywhere you stand under it, including on the raised deck, with the poles placed outboard so they stay out of the casting arc.
Will an aft shade clear shallow-water anchors or a poling platform on the transom?
Yes. The aft poles stand in the gunwale rod holders forward of the transom, and the aft edge of the panel is built to the measurement you give us from the mount point to those rod holders. Shallow-water anchors on the transom corners and a poling platform both sit aft of that edge and above or below it, and the panel does not touch them. If you pole from the platform, the shade is down in about 30 seconds and bagged, and back up at the next stop in under a minute.
Can you match the shade to my Haynie's hull color?
Close to it. Stamoid comes in 14 colors, and most owners either match the hull or run a neutral like white or sand that keeps the underside bright. Send us a photo of the boat and we will send back the two or three colors that work with it. A dark shade looks sharp but reads warmer underneath; a light one reflects more and is the better choice for a boat that sits at anchor on the flats in August.
Will Gemlux rod holders look right next to the stainless already on my Haynie?
Yes. Gemlux rod holders are polished stainless flush mounts and sit alongside the factory stainless cleats, rails and holders on a Haynie without looking like an add-on. We only specify Gemlux because a shade pole loads a rod holder sideways in a way a rod never does, and a cheap holder will work loose or crack the gelcoat around it. If your existing rod holders are already where the poles need to stand, you may not need any, and we tell you that before you order.
More builders we shade
BlackJack · Majek · NauticStar · Sea Born · Shoalwater · Blue Wave · Carolina Skiff · Crevalle
Sunshades by boat type
Center Console · Dual Console · Sport Fisher · Yachts · Nordhavn · Superyachts
How we build them
How a Sunshade Is Made · Why Stamoid · Carbon Poles · Gemlux Rod Holders · What It Costs · Running With It Up · Ordering Out of State
Measured and installed at your boat
Miami · Fort Lauderdale · Palm Beach · Jupiter · Stuart & Fort Pierce · Charleston SC
Shade the boat that was built for the Coastal Bend
Order the full kit, shade only, or call (561) 270-6922, 8am to 4pm Eastern, Monday through Friday.
Or call (561) 270-6922Tell us about your Haynie
Send a few details and a couple of photos and we reply with a fixed price on a shade built for your boat. Local to South Florida? We come to you. Anywhere else in the country? We ship you a kit.
Prefer to talk? Call or text (561) 270-6922, 8am to 4pm ET Monday to Friday.