Custom Marine Sunshades · Delray Beach · Since 1974

Edgewater Boat Sun Shades, Patterned to Your Deck

Edgewater builds in Edgewater, Florida, on the east coast between Daytona and the Space Coast, so the boats are born into the same sun we build for. An Edgewater owner in Florida is not asking whether the sun is a problem. They are asking how to get the family off the boat at four o'clock without everyone cooked.

The hardtop on a 262CC shades the helm, and the helm is where nobody sits once the anchor is down. The bow seating, the forward lounge on a 248CX, the cockpit on a 310SC: these are the parts of the boat people use at a sandbar, and the factory top does nothing for them. A Sunshade fixes that, and it comes down in about 30 seconds when you want the deck back.

We have built custom marine canvas in Delray Beach since 1974, and Sunshades are the thing we do most. Full kits from $1,895 with poles, quick-release mounts and hardware, shade only from $845 if you already have poles, free shipping anywhere in the US. See all our custom Sunshades.

We are not affiliated with Edgewater Boats. We build canvas that fits their boats.

Edgewaters we build for

Edgewater's current range runs in three families. Model names are exactly as Edgewater writes them.

  • Outrider: 158CS, 170CC, 188CC, 208CC. Small, light, often trailered and often run without a hardtop. The shade is usually a freestanding rig on four telescoping poles.
  • Center Console: 230CC, 250CC, 262CC, 285CC, 325CC, 340CC. The core of the brand. A hardtop is the normal spec from the 230CC up, which puts these in the standard build: quick-release mounts on the forward edge of the top, two carbon fiber poles in the bow rod holders, panel flying forward over the bow seating.
  • Crossover: 248CX, 262CX, 280CX, 310SC. Edgewater's dual console line, the boats it describes as marrying a bowrider with a center console. Bow lounge forward, a wide cockpit aft, and on the 310SC a cabin. These are the Edgewaters most likely to want bow and aft together.

If you run one of the earlier Edgewater dual consoles with a DC suffix, the build is the same as the current CX boats.

Edgewater is one of a handful of Florida builders we see constantly, alongside Boston Whaler, Everglades and Grady-White. Comparing a 230CC with a Scout of the same length? Our Scout page covers that boat.

Center console, Crossover and Outrider each want a different shade

The three Edgewater families put the top, the seating and the rod holders in different places, and the shade follows those three things.

Center consoles (230CC through 340CC). The hardtop is the anchor point. Our quick-release mounts screw to the forward edge of the top, the panel clips on there, and it flies forward to two poles standing in the bow rod holders. If the boat has no forward rod holders, common on a 230CC or 250CC optioned for family use, we install Gemlux rod holders in the gunwale, placed so the poles stand clear of the bow walkway. On the 325CC and 340CC the bow is wide enough that owners often step up to four poles, and an aft shade off the back of the top is a common second order because the cockpit is big.

Crossovers (248CX, 262CX, 280CX, 310SC). A dual console has a windshield and a bow lounge forward, and the top, where fitted, sits over the helm and passenger console. The bow shade attaches to the forward edge of that top and flies forward over the lounge, set high enough that adults sit upright underneath. Aft, the cockpit on a 262CX or 280CX is where lunch happens, so the aft panel runs off the back edge of the top to two poles in the aft gunwale rod holders. The 310SC has a cabin and a bigger top, which gives us more to mount to. Bow and aft together saves about 10%.

Outriders (158CS, 170CC, 188CC, 208CC). With no top there is nothing overhead to hang from, so the shade stands on its own: four carbon fiber telescoping poles in rod holders, the panel tensioned between them. It packs small enough to live in the console, which matters on a trailer boat that sleeps in a garage. Small boats are where a shade changes the day the most, because there is nowhere else on board to get out of the sun.

Tell us the model and whether the boat has a top, and the build is settled in one question.

What goes into an Edgewater Sunshade

Every shade we build, for Edgewater or anyone else, is built to one standard.

  • Stamoid fabric, in 14 colors. Stamoid is 100% waterproof, blocks UVB completely, and is backed by a 5-year warranty. In practice it lasts a good deal longer, because a Sunshade is deployed for a few hours at a time rather than left standing in the sun year round, and the shades we have built have run 10 years and more. It is the only fabric we put on a Sunshade, on purpose: light, sheds water, stuffs into its bag wet.
  • Lifetime thread (PTFE). Thread is where cheap shades fail first. Ours outlasts the fabric.
  • Double-reinforced sides and triple-reinforced corners. The corners carry the load of the tension line, so they get the most material.
  • Catenary edges. Every edge is cut in a shallow curve, so that when the corners are tensioned the whole edge pulls tight. A straight-cut edge sags in the middle and flaps.
  • Patterned in 3D to the boat, built to the mount-to-mount number to an eighth of an inch. That is why it pulls tight and clean on the first try.
  • Carbon fiber telescoping poles, black, standard. Stainless on request. Pole bases sit in the rod holders; the other edge attaches to quick-release mounts on the top.

Up in under 60 seconds by one person, down in about 30. For the full process see how National Canvas builds a Sunshade.

Edgewater owners from Jupiter to Miami, and everywhere else

From Miami to Jupiter we come to the boat: measure at the dock or on the trailer, build in Delray Beach, come back and install. Each truck carries rod holders, carbon fiber poles, mounts and hardware, so a local install, including drilling new rod holders, is done in one visit. The Treasure Coast is served by appointment.

Everywhere else, you measure with our card and a phone or video walkthrough, we pattern from those numbers, and the kit ships free anywhere in the United States with no sales tax outside Florida. Most owners self-install in an afternoon with a drill and a tape measure. Boats to 50 ft are priced online; over 50 ft, call.

Questions

Edgewater Sun Shades FAQ

My Edgewater 262CC has the factory hardtop. Do you mount to it, and does that void anything?

We mount to it, and it is the right place to mount. Our quick-release fittings are low-profile 316 stainless pieces that screw to the forward edge of the hardtop with small fasteners, bedded and sealed. The top on a 262CC is more than strong enough to carry a tensioned bow panel, and the load is spread across the mounts rather than concentrated on one point. If a warranty question worries you, ask your Edgewater dealer before we drill. We will give you the exact fastener size and location so they can answer with facts.

The bow seating on my 248CX has cushions and a filler. Will the shade sit high enough to use it?

Yes. On a Crossover we set the panel height and the pole height so an adult can sit upright on the bow lounge without the fabric at head level, and so you can step through the bow with the shade up. The panel is tensioned flat, not draped, so there is no belly in the middle. If you use the bow filler as a sun pad, say so, and we will set the poles outboard of where people lie.

My Outrider 208CC has no T-top at all. Can you still shade it?

Yes, and it is a common build. With no top, the shade becomes a four-pole freestanding rig: carbon fiber telescoping poles in rod holders at the four corners of the area you want covered, panel tensioned between them. If the 208CC does not have rod holders where the poles need to be, we install Gemlux rod holders there, or you drill them from our layout on a remote order. The whole kit packs small enough for the console locker.

I keep the 285CC in Stuart. Is that in your install area?

Yes, by appointment. The daily route runs Miami to Jupiter; Stuart, Fort Pierce and Vero Beach get a scheduled date. We usually combine the measure and the rod holder install into one visit and the shade install into a second, or, if you are comfortable with a drill, we measure in person and ship the finished kit to you. Call (561) 270-6922 and we will work out which makes sense for your dock.

Can the Edgewater shade stay up while I run back to the ramp?

You can run at up to 25 mph with the shade up, and pulling the tension line tight buys a little more. Above that, take it down. It comes down in about 30 seconds and goes back up in under 60, by one person, so running fast is a non-issue. Most owners drop it when they pull the anchor and put it back up at the next stop.

What does a Sunshade for an Edgewater cost?

Full kits start at $1,895, which includes the shade, carbon fiber telescoping poles, quick-release mounts and hardware. Shade only starts at $845 if you already have poles. A two-pole bow shade on a 230CC or 250CC sits at the low end of the range. A 340CC with four poles and a bow and aft pair runs higher, and ordering bow and aft together saves about 10%. Free shipping anywhere in the United States, no sales tax outside Florida, price fixed before you approve the spec.

Shade the Edgewater the way it was meant to be used

Order a full kit from $1,895 or a shade only from $845 at the store, or call (561) 270-6922, 8am to 4pm Eastern, Monday through Friday.

Or call (561) 270-6922
Free Quote Within One Business Day

Tell us about your Edgewater

Send a few details and a couple of photos and we reply with a fixed price on a shade built for your boat. Local to South Florida? We come to you. Anywhere else in the country? We ship you a kit.

Prefer to talk? Call or text (561) 270-6922, 8am to 4pm ET Monday to Friday.
This field is for validation purposes and should be left unchanged.
Two photos help most: your T-top from the side, and your rod holders. Photos on your phone? You can also text them to (561) 270-6922.
Drop files here or
Accepted file types: jpg, jpeg, png, heic, webp, Max. file size: 20 MB, Max. files: 4.

    Let's Talk

    This field is for validation purposes and should be left unchanged.

    Start Your Project

    Let’s start the conversation. Share a few details and we will be in touch.