Custom Marine Sunshades · Delray Beach · Since 1974

Cobia Sun Shades, Cut to Your Deck

Cobia is built by Maverick Boat Group in Fort Pierce, Florida, about 70 miles up the coast from our shop in Delray Beach. That makes Cobia one of the few builders whose boats we can shade in the same water they were built in.

The current lineup is nine boats: seven center consoles from the 245 CC to the 350 CC, including the 285 Open, and two dual consoles, the 250 DC and 280 DC. Cobia fits a fiberglass hardtop as standard across the range, and that hardtop does exactly one job: it shades the helm. Once the anchor is down nobody is at the helm. They are in the bow, where there is nothing overhead at all.

We have built custom Sunshades in Delray Beach since 1974. Each one is patterned in 3D to the boat, sewn in Stamoid, and goes up in under 60 seconds by one person. Full kits from $1,895 with poles, quick-release mounts and hardware, shade only from $845 if you already have poles, free shipping anywhere in the United States, no sales tax outside Florida.

We are not affiliated with Cobia or Maverick Boat Group. We build canvas that fits their boats.

What Cobia's layouts mean for the shade

The CC models (245 CC through 350 CC). Cobia's center consoles carry a hardtop with an integrated frame and glass windshield as standard, and that hardtop is the mounting point. The quick-release mounts screw to the hardtop's forward edge on the console side, the shade flies forward over the bow seating with its folding backrests, and two carbon fiber telescoping poles stand in the forward gunwale rod holders to tension it. On the 245 CC and 265 CC that is a two-pole panel. From the 285 CC up, the beam and bow length push us to four poles so the panel stays flat in a breeze. The 320 CC and 350 CC are big enough that bow and aft together is the normal order, and the aft panel has to clear the outriggers and the cockpit rod holders.

The 285 Open. This is the 285 CC hull with the console opened up for full walk-up access to the bow and stern, a bow cushion package with forward-facing backrests, and a stowable bow insert. For a shade that means the bow is a lounge, not a casting deck, and the panel height is set so people can sit upright with the backrests up. The walk-around stays clear because the poles stand outboard in rod holders.

The dual consoles (250 DC, 280 DC). A full windscreen and a walk-through instead of a center console, with a fiberglass hardtop standard. The aft edge of the shade attaches to the hardtop's forward edge and the forward edge tensions to poles in the bow, over the forward sun lounge. Cobia offers an optional electric cockpit shade on the 280 DC, and it is worth knowing what it covers: the cockpit, aft of the windscreen. The bow lounge, where everyone sits at anchor, is still open. That is the part we cover.

Cobias we build for

  • 245 CC and 265 CC. Two-pole bow shade off the hardtop. The cleanest build in the range.
  • 285 CC and 285 Open. Four poles. The Open gets the lounge treatment described above.
  • 305 CC and 320 CC. Four-pole bow panels; bow and aft together for anyone who fishes the cockpit.
  • 350 CC. Bow and aft, six poles, large panels. Call us on this one.
  • 250 DC and 280 DC. Windshield-frame or hardtop mount, poles forward.

See all our custom Sunshades. Cobia shares a factory with Pathfinder, and we build for both. If you are cross-shopping, we also build for Grady-White, Sea Hunt and Boston Whaler.

What a Cobia shade is made of

Every shade we build is Stamoid, and that is a deliberate choice. Stamoid is 100% waterproof, blocks UVB completely, and is backed by a 5-year warranty. In practice it lasts a good deal longer, because a Sunshade is deployed for a few hours at a time rather than left standing in the sun year round, and the shades we have built have run 10 years and more. It comes in 14 colors, and a Cobia hull with factory canvas usually has an obvious match among them.

Sewn with lifetime thread (PTFE), double-reinforced sides, triple-reinforced corners because the corners carry all the tension, and a catenary curve cut into every edge. A straight-cut edge sags in the middle and flaps. A catenary edge pulls tight and clean across its whole length when the corners are tensioned.

The panel is patterned in 3D to your boat's actual measurements and built to the mount-to-mount number to an eighth of an inch. Poles are black carbon fiber telescoping poles as standard, stainless on request. When a boat needs rod holders added for the poles, we install Gemlux rod holders only. Our guide on how we build a Sunshade walks through the whole process from measurement to bag.

Built two hours from the Cobia factory, installed in the same water

From Miami to Jupiter our technicians are on the road every day. A technician measures at your slip or on the trailer, we build in Delray Beach, and we come back and install, with the truck carrying rod holders, poles, mounts and hardware so the whole job is done in one visit.

Cobias cluster north of that, in the water they were built in. We serve the Treasure Coast, Stuart, Fort Pierce and Vero Beach, by appointment. If your Cobia lives in Fort Pierce or Stuart, see our Fort Pierce and Stuart page for how a local measure and install works up there.

Everywhere else in the country, you measure with our card and a phone or video walkthrough, we build to your numbers, and the shade ships free anywhere in the United States with no sales tax outside Florida. Most owners self-install in an afternoon with a drill and a tape measure.

Running with the shade up

You can run at up to 25 mph with the shade up, and pulling it tight buys a little more. Past that, take it down. It comes down in about 30 seconds and goes back up in under 60, so running fast is a non-issue. It stuffs into its bag without careful folding, and because Stamoid is waterproof it can be stowed wet.

Questions

Cobia Sun Shades FAQ

What does the 285 Open's open-bow layout change about the shade?

It changes the height and the pole positions. The 285 Open is built for full walk-up access to the bow, with forward-facing backrests and a stowable bow insert, so the bow is a lounge and people sit in it facing aft. We set the panel high enough that an adult can sit upright with the backrests up, and we keep the poles outboard in rod holders so the walk-around stays open. The panel itself is patterned to the same hardtop forward edge as the 285 CC, so the mount points are the same. It is the forward end that is different.

Can a 250 DC or 280 DC take a bow shade with the windscreen and walk-through?

Yes. Both ship with a fiberglass hardtop, so the aft edge of the shade attaches to the hardtop's forward edge and the forward edge tensions to telescoping poles standing in the bow. The walk-through stays clear because the panel sits above head height at the windscreen and the poles are outboard. The forward sun lounge sits fully under it. If the bow has no rod holders, we add Gemlux rod holders during a local install or ship them with the kit with a drilling diagram.

My Cobia has the factory hardtop with the glass windshield. Where do the mounts go?

On the forward edge of the hardtop, console side, well clear of the windshield frame and the glass. The quick-release mounts are small stainless fittings screwed to the top. We are not drilling anywhere near the tempered glass or the wiper, and the hardtop's forward edge on a Cobia is solid enough to carry the load. On a local install we fit them during the visit. For a shipped kit the mounts come with the exact spacing marked and the panel is built to that mount-to-mount number.

What happens on install day in Stuart or Fort Pierce?

A technician comes to the boat by appointment, measures, and photographs the hardtop edge and the rod holder positions. We build the shade in Delray Beach and come back to install it. The truck carries rod holders, poles, mounts and hardware, so if the boat needs rod holders drilled and fitted for the poles, that happens on the same visit. You get a walkthrough of putting it up and taking it down before we leave, which on a Cobia takes about a minute each way.

Does the shade interfere with the outriggers on a 320 CC or 350 CC?

Not on the bow, because the bow panel runs forward of the hardtop and the outriggers are mounted on the top itself. On the aft panel, which is the one most 320 CC and 350 CC owners add second, we pattern around the outrigger bases and the cockpit rod holders so the panel does not lay across them. The outriggers can stay rigged with the aft shade up at anchor. If you troll with them out, the shade comes down first, which is about 30 seconds.

Cobia also builds in Fort Pierce. Can you shade a new boat before I pick it up?

We install at your slip or your ramp, not at the factory or the dealer, so the practical answer is to order the shade while the boat is on order and have us measure it the first week it is in the water. If you are on the Treasure Coast that is an appointment. If you are taking delivery elsewhere in the country, send us the model and we will tell you what we already know about the layout, then confirm the five measurements with you over a video call once the boat is yours.

Shade the bow of your Cobia

Order the full kit from $1,895, the shade only from $845, or call (561) 270-6922, 8am to 4pm Eastern, Monday through Friday.

Or call (561) 270-6922
Free Quote Within One Business Day

Tell us about your Cobia

Send a few details and a couple of photos and we reply with a fixed price on a shade built for your boat. Local to South Florida? We come to you. Anywhere else in the country? We ship you a kit.

Prefer to talk? Call or text (561) 270-6922, 8am to 4pm ET Monday to Friday.
This field is for validation purposes and should be left unchanged.
Two photos help most: your T-top from the side, and your rod holders. Photos on your phone? You can also text them to (561) 270-6922.
Drop files here or
Accepted file types: jpg, jpeg, png, heic, webp, Max. file size: 20 MB, Max. files: 4.

    Let's Talk

    This field is for validation purposes and should be left unchanged.

    Start Your Project

    Let’s start the conversation. Share a few details and we will be in touch.