Custom Marine Sunshades · Delray Beach · Since 1974

Carolina Skiff Sun Shades, Cut to Your Deck

Carolina Skiff builds in Waycross, Georgia, and has for more than thirty years, and the thing that makes a Carolina Skiff a Carolina Skiff is also what makes the shade a different job: most of them have no T-top, and plenty have no rod holders where a Sunshade pole needs to stand.

That does not rule out a shade. It changes the build. On a boat with a T-top the shade hangs off the top on one edge and two poles on the other. On a skiff with nothing over the console, the shade stands on its own, on four telescoping poles in four rod holders, and if the boat does not have four holders in the right places we add Gemlux rod holders with the kit. It is a routine order for us, not a special one.

Why bother on a skiff? Because a skiff has the least shade of anything on the water. No console roof, no cabin, no hardtop, and the people on it are sitting a foot off the water at noon. A Sunshade is the only shade the boat will ever have.

Up in under 60 seconds by one person, down in about 30. Patterned in 3D to your hull, sewn in Delray Beach. Full kits from $1,895, shade only from $845 if you already have poles, free shipping nationwide. See all our custom Sunshades.

We are not affiliated with Carolina Skiff, LLC. We build canvas that fits their boats.

Carolina Skiffs and Sea Chasers we build for

Carolina Skiff runs four series under its own name and sells Sea Chaser as a separate brand from the same company.

  • LS Series: 17 LS, 19 LS, 21 LS, 23 LS, 25 LS. The flat-bottom workhorse, center console, with a bimini, a canvas T-top, a fiberglass hard-shell T-top or a molded hardtop all offered as options. The 23 LS is 23 ft 2 in on a 96-inch beam with four rod holders in the leaning post. Which top you ordered decides the build.
  • JLS Series: 162 JLS, 178 JLS, 192 JLS. Smaller hulls, mostly run open. Freestanding four-pole shade, holders added.
  • Ultra Elite Series: 19, 21, 22, 23, 24, 26 Ultra Elite. The step-up hull with wrap-around bow seating. The 23 Ultra Elite is 22 ft 11 in on a 98-inch beam, with eight under-gunnel rod positions and the same four top options as the LS. The most common T-top-mounted shade in the range.
  • E Series: E16 JVX, E18 JVX, E20 JVX CC, E21 DLX, E24 DLX, and the EV180, EV198 and EV218 Sea Skiff. The JVX and DLX come as center console or tiller handle. The E20 JVX CC is 19 ft 11 in on a 78-inch beam with two rod holders on the console and no top listed. A narrow freestanding build.
  • Sea Chaser: 20 HFC, 22 HFC, 24 HFC; 21 LX, 23 LX, 26 LX Bay; 27 HFC and 30 HFC. More conventional hulls that more often carry a T-top, so the shade mounts the conventional way.

Other builders in the same water: Key West, Pathfinder, Tidewater and Sea Fox.

No T-top is the normal case, so the freestanding build matters

With a T-top or hardtop. On an LS, Ultra Elite or Sea Chaser with a canvas or fiberglass T-top, the shade's inboard edge attaches to quick-release mounts screwed to the top and the outboard corners tension to two carbon fiber telescoping poles standing in the gunnel rod holders. Two poles, simplest install, and it is the same build as any center console.

With a bimini or nothing. A bimini folds and is not built to take tension, so we never mount to one. The shade becomes a freestanding panel on four telescoping poles, two forward and two aft of the area you want covered, standing in four rod holders. It tensions corner to corner across the poles, and because every edge is cut on a catenary curve it pulls tight and clean without a top to pull against.

No rod holders. The leaning post holders on an LS point the wrong way for a pole, the eight rod positions on an Ultra Elite are horizontal racks under the gunnel, and a JVX has two on the console. So on most Carolina Skiffs the kit ships with Gemlux rod holders, the only holders we install, and we tell you where to put them: outboard in the gunnel, clear of the walkway, at the corners of the shade. On a T-top boat that lacks forward holders, the quick-release mounts go on the top and two Gemlux holders go forward.

Narrow beams. A 78-inch JVX and a 96-inch LS are narrow boats, which is a help. The panel is small, two poles cover the width, and the shade sits at the low end of our price range. A tiller-handle JVX or DLX with no console at all gets a freestanding four-pole shade over the middle of the boat, with the tiller position left clear.

The same standard as a 40-footer

A skiff shade is built exactly like the ones we build for sport fishers. Stamoid fabric, the only fabric we use on a Sunshade, and a deliberate choice. Stamoid is 100% waterproof, blocks UVB completely, and is backed by a 5-year warranty. In practice it lasts a good deal longer, because a Sunshade is deployed for a few hours at a time rather than left standing in the sun year round, and the shades we have built have run 10 years and more. Fourteen colors.

Lifetime thread (PTFE) on every seam. Double-reinforced sides, triple-reinforced corners, because on a freestanding shade the corners carry everything. Catenary curves on every edge, cut in a shallow arc so that when the corners are tensioned the whole edge pulls tight and clean, no sag, no flap. Patterned in 3D to the boat's actual measurements and built to the mount-to-mount number to an eighth of an inch. Black carbon fiber telescoping poles standard, stainless telescoping on request. More on the holders in Gemlux rod holders for Sunshade poles.

Up the creek with the shade up

You can run at up to 25 mph with the shade up, and pulling it tight buys a little more. It comes down in about 30 seconds and goes back up in under 60, one person, no tools, so running fast is a non-issue. It stuffs into its bag with no folding and can go away wet.

Measured at the boat in South Florida, shipped anywhere else

From Miami to Jupiter our technicians are on the road every day, each truck stocked with rod holders, carbon fiber poles, mounts and hardware. We measure at the boat, build in Delray Beach, and come back to install, including drilling and fitting the Gemlux holders, in one visit. The Treasure Coast is served by appointment.

Everywhere else, including Georgia and the Carolinas where most of these boats live, you measure with our card and a phone or video walkthrough, we build, and the shade ships free anywhere in the US with no sales tax outside Florida. Most owners self-install in an afternoon with a drill and a tape measure.

Order the full kit from $1,895, poles, quick-release mounts and hardware included, or the shade only from $845 if you already have poles. Bow and aft together saves about 10%.

Questions

Carolina Skiff Sun Shades FAQ

My Carolina Skiff has no T-top and no rod holders at all. Is a shade even possible?

Yes, and it is the most common Carolina Skiff order we get. The shade stands on four telescoping poles in four rod holders, so the only thing the boat needs is four holders in the right places. We ship Gemlux rod holders with the kit and mark where they go on your measure card: outboard in the gunnel, at the corners of the shade, clear of where you walk. Each one is a hole-saw cut and four screws. Once they are in, the shade goes up in under a minute.

Can a freestanding shade stay tight with nothing solid to pull against?

Yes. The tension runs corner to corner across the four poles, and the poles lock at height, so the panel is pulled against the poles, not against a top. What keeps it from sagging in the middle is the catenary curve cut into every edge; when the four corners are tensioned the whole edge pulls tight and clean. A straight-cut panel on four poles sags and flaps, which is why universal kits look the way they do.

Does a shade work on a tiller-handle JVX with no console?

It does. With no console, the whole deck is open and the shade covers the middle of the boat on four poles, leaving the tiller position aft and the bow clear. We set the pole positions from a few photos of the boat so the panel sits where people actually sit, usually over the cooler and the bench. These are the smallest shades we build and the price sits at the low end.

I have the 23 LS with the canvas T-top. Does the shade mount to canvas?

It mounts to the T-top frame, not the canvas. The quick-release mounts screw to the aluminum tube at the forward edge of the top, and the shade's inboard edge clips to them exactly as it would on a fiberglass hardtop. The outboard corners go to two poles in rod holders forward. The canvas top takes no load; the poles and the frame carry it.

Does the Ultra Elite's under-gunnel rod storage work for the poles?

No. The eight rod positions on an Ultra Elite are horizontal racks under the gunnel for storing rods, not vertical holders a pole can stand in, and the leaning post holders point aft and up. The poles need a vertical, flush-mount holder in the gunnel, so an Ultra Elite gets two or four Gemlux holders added depending on whether it has a top. Nothing about the factory rod storage changes.

Will a shade add much weight or clutter to a small skiff?

Very little. Carbon fiber telescoping poles are light, the Stamoid panel on a 17 to 21 foot skiff is small, and the whole kit stuffs into one bag that fits under a seat. When the shade is down, the only thing left on the boat is four flush rod holders you will use for rods anyway. There is no frame to stow, no bows, no hardware beyond the holders.

Give the skiff the only shade it will ever have

Order online, or call (561) 270-6922, 8am to 4pm Eastern, Monday through Friday, and we will set a measure or send the card.

Or call (561) 270-6922
Free Quote Within One Business Day

Tell us about your Carolina Skiff

Send a few details and a couple of photos and we reply with a fixed price on a shade built for your boat. Local to South Florida? We come to you. Anywhere else in the country? We ship you a kit.

Prefer to talk? Call or text (561) 270-6922, 8am to 4pm ET Monday to Friday.
This field is for validation purposes and should be left unchanged.
Two photos help most: your T-top from the side, and your rod holders. Photos on your phone? You can also text them to (561) 270-6922.
Drop files here or
Accepted file types: jpg, jpeg, png, heic, webp, Max. file size: 20 MB, Max. files: 4.

    Let's Talk

    This field is for validation purposes and should be left unchanged.

    Start Your Project

    Let’s start the conversation. Share a few details and we will be in touch.