Boat Sun Shades for Jupiter, Tequesta and the Loxahatchee
Jupiter is the north end of our daily route. A technician leaves Delray Beach every working day and works the coast up to the Jupiter Inlet, so a boat in Tequesta or Palm Beach Gardens gets measured at the dock and installed at the dock, same as one in Boca.
National Canvas has built marine canvas in Delray Beach since 1974, 52 years, and Sunshades are now the center of the business. Jupiter boating is sandbar boating: the inlet sandbar below the lighthouse, the Loxahatchee, the flats behind Jupiter Island. The boat spends the afternoon stopped in bright water with no shade over anybody.
The shade we build flies off the T-top or hardtop out over the bow or the cockpit on carbon fiber poles, goes up in under 60 seconds by one person, and stuffs into a bag when you want the deck back. Full kits from $1,895, shade only from $845 if you already have poles, and local jobs are quoted at the boat. See all our Sunshades, or call (561) 270-6922.
Clear water, low tide, and a sandbar with no shade
The Jupiter sandbar is the center of a Jupiter weekend. Boats start arriving mid-morning, raft up in sight of the lighthouse, and wait on the tide to drop enough to stand. By early afternoon the water is ankle deep, the sun is straight overhead, and the only shade on any boat is the hardtop over a helm nobody is standing at.
The water here makes it worse. The Jupiter Inlet runs clear and the bottom is light sand, so the sun comes at you from below as well as above. A shade that only blocks the vertical leaves the crew squinting off the water. Ours are cut wide enough to put people in shadow, not just the cushions.
The Loxahatchee is the other half of the day: a slow, mangrove-lined river with long no-wake stretches, and a slow boat in July air has no breeze over the deck. Owners want a shade that stays up at idle and comes down fast at the inlet.
Marinas and water from Hobe Sound to North Palm Beach
We measure and install at the slip, the lift, the dry stack and the ramp. The docks we see most on the north end of the route:
- Jupiter Pointe Club and Marina, Tequesta. On the Intracoastal at the Loxahatchee, over 150 wet slips to 60 feet plus dry storage, minutes from the Jupiter Inlet.
- Blowing Rocks Marina, Tequesta. 60 slips to 70 feet and dry storage, looking across at Jupiter Island.
- Jupiter Yacht Club Marina. 79 slips to 65 feet, a mile from the inlet and the lighthouse.
- Loggerhead Marina Jupiter, inside Jonathan's Landing. Dry storage for boats to 40 feet and wet slips to 60. Most of what comes out of the racks here is a 24 to 36 foot center console.
- Soverel Harbour Marina, Palm Beach Gardens. 146 slips to 100 feet just north of the PGA Boulevard bridge.
- Safe Harbor Old Port Cove, North Palm Beach. 203 slips to 200 feet, no bridges to the inlet.
The water itself: the Jupiter Inlet and the sandbar just inside it, the Loxahatchee River, the Intracoastal along Jupiter Island to Hobe Sound, and the beach off Juno when the ocean lays down. Private docks and lifts along the river and the Intracoastal are a normal day for us.
Jupiter boats in Jupiter, and the rest of the fleet
Jupiter is a center console town. The hulls we pattern most, with a page for each:
- Jupiter. The name is a coincidence of geography: Jupiter Marine builds on the Gulf coast in Palmetto, not here. But the 30 to 43 foot forward-seating hulls are everywhere on this water, and the bow lounge is the first thing owners want covered.
- Pathfinder. Bay boats on lifts along the Loxahatchee, the boat for the river and the flats.
- Contender and Yellowfin. The offshore fleet out of the inlet. Aft shades over the cockpit for the days the boat is not fishing.
- Scout. Family center consoles and dual consoles, heavy on bow seating.
- Grady-White. Freedom dual consoles and Canyon center consoles, the all-around boat here.
- Sportfish and express boats to 80 feet and up. Old Port Cove and Soverel are full of them. See our Superyacht Sunshades.
We are not affiliated with any builder. We know their tops and where the rod holders and quick-release mounts need to land, and that is most of the job.
Measured at the dock, built in Delray Beach, installed at the dock
- Call with the boat and the dock. Year, make, model, bow or aft or both, and where it lives. We put you on the route, usually within the week.
- A technician measures at the boat. He checks the T-top or hardtop for mount positions, confirms where the pole bases sit, and takes the mount-to-mount numbers to an eighth of an inch. If the boat needs rod holders for the poles, he marks them. You get a written quote before anything is cut.
- We build it in Delray Beach. Patterned in 3D to your boat's actual measurements, cut, and sewn in our shop.
- We come back and install. Every truck is stocked as a shop on wheels: Gemlux rod holders, carbon fiber poles, quick-release mounts, hardware and tools. Drilling and fitting new rod holders and mounts happens on the spot, and the shade is up and tensioned before we leave. One visit, finished.
Because Jupiter is the far end of the day, we batch north-county measures and installs together. If a neighbor at the same dock wants one, say so; it usually gets both of you an earlier date.
The construction standard
- Stamoid, one fabric by choice. Stamoid is 100% waterproof, blocks UVB completely, and is backed by a 5-year warranty. In practice it lasts a good deal longer, because a Sunshade is deployed for a few hours at a time rather than left standing in the sun year round, and the shades we have built have run 10 years and more. 14 colors.
- Lifetime thread (PTFE) on every seam. The thread outlasts the fabric, not the other way around.
- Double-reinforced sides and triple-reinforced corners. The corners carry the tension.
- Catenary curves on every edge. The edges are cut in a shallow curve, so when the corners are tensioned the whole edge pulls tight, with a sleek look and no flapping. A straight-cut edge sags in the middle and flaps.
- Patterned in 3D to the boat. Built to the mount-to-mount number to an eighth of an inch, so it tensions tight and clean the first time.
- Carbon fiber telescoping poles, black, standard. Stainless on request. The pole bases sit in rod holders; the other edge clips to quick-release mounts screwed to the top.
You can run at up to 25 mph with the shade up, and pulling it tight buys a little more. It comes down in about 30 seconds and goes back up in under 60, so running fast is a non-issue.
Quoted at the boat, or order the kit online
For a boat anywhere from Hobe Sound to North Palm Beach, the normal path is a measure visit and a written quote. Full kits start at $1,895 with poles, quick-release mounts and hardware included. Shade only starts at $845 if you already have poles. Bow and aft together saves about 10%. The quote covers the shade, any rod holders and mounts the boat needs, and the install.
Or order the full kit online from $1,895 or shade only from $845, send us your measurements, and we build and ship it free. Length brackets go to 50 feet online; over 50 feet, call for a quote. We answer the phone 8am to 4pm Eastern, Monday through Friday, at (561) 270-6922.
Jupiter FL Sun Shades FAQ
Is Jupiter really inside your daily service area, or is that a stretch?
It is inside it, and it is the top of it. Technicians run Miami to Jupiter every working day, and the north end of that route covers Jupiter, Tequesta, Juno Beach, Palm Beach Gardens, North Palm Beach and Hobe Sound. The only practical difference from a Delray Beach job is scheduling: we group north-county measures and installs together, so your date may be a few days further out than a boat in Boynton. The visit itself is identical. Measure at the dock, build in Delray Beach, install at the dock.
Do you build shades for Jupiter-brand boats specifically?
Yes, and we build a lot of them here, because a Jupiter in Jupiter is about the most common boat on this water. The 30 to 43 foot forward-seating hulls have a bow lounge that is the first thing owners want covered, and we have patterned their T-tops and hardtops many times, so we know where the quick-release mounts land and where the pole bases need rod holders. The builder itself is in Palmetto on the Gulf coast. We are not affiliated with Jupiter Marine; we build canvas that fits their boats.
Which is better for the Jupiter sandbar, a bow shade or an aft shade?
For a sandbar day, the bow shade, because that is where people sit when the boat is anchored bow-in with the stern to the channel. The bow lounge on a forward-seating center console is the social end of the boat, and a bow shade off the T-top covers it completely. An aft shade earns its place on boats where the crew lives in the cockpit, and on fishing boats on their off days. Owners who want both buy both; bow and aft together saves about 10%.
Can I leave the shade up idling the Loxahatchee River?
Yes. Idle speed and no-wake stretches are exactly what the shade is built for. You can run at up to 25 mph with it up, and pulling it tight buys a little more, so the long slow run up the river and back is a non-issue. When you reach the inlet and want to open the boat up, it comes down in about 30 seconds and stuffs into its bag, and it goes back up in under 60 when you anchor. Most owners leave it up from the dock to the sandbar and never think about it.
My boat is dry stacked at Loggerhead. Can you still measure and install it?
Yes. We coordinate with the marina to have the boat pulled for the measure and again for the install, and we drill and fit the rod holders and mounts while it is on the ground or in the water. Loggerhead and Jupiter Pointe are used to this; a day's notice is usually enough. If the boat is going in the water for a weekend anyway, we schedule the install for that morning and save the yard a lift. You do not need to be there if the marina can give us access.
What happens if the shade is wet when I get back to Tequesta, or we get caught in an afternoon storm?
Nothing you need to manage. Stamoid is 100% waterproof, so the shade does not absorb water. When the afternoon cell comes over the Loxahatchee, pull the quick-release mounts, drop the poles, and stuff the shade into its bag wet. No careful folding, no drying out on the dock. It comes back out tight and clean the next time. If you want to leave it up through a light shower at anchor, the waterproof panel sheds rain and the catenary edges keep it from pooling.
Shade for the sandbar, from the north end of the route
Call (561) 270-6922 to get a Jupiter, Tequesta or Palm Beach Gardens boat on the schedule, or order the kit online from $1,895.
Or call (561) 270-6922Tell us about your boat
Send a few details and a couple of photos and we reply with a fixed price on a shade built for your boat. Local to South Florida? We come to you. Anywhere else in the country? We ship you a kit.
Prefer to talk? Call or text (561) 270-6922, 8am to 4pm ET Monday to Friday.